1. process allows them to be moves from

1.Manual  assembly and manualcomponent repair is more difficult and requires highly skilled operators and moreexpensive tools, this is due to the small component sizes and lead spacing’s ofmany SMDs. Handling of small surface mount technology components canbe difficult, requiring tweezers, unlike nearly all through-hole components.  through-hole components will stay in place (bygravity) once in place and can be mechanically secured prior to soldering bybending out two leads on the solder size of the board, SMDs are easily movedout of place by a touch of a soldering iron. Without expert skill, whenmanually soldering or de-soldering a component, it is easy to reflow the solderof a nearby component and unintentionally move it by accident, something thatis very difficult to do with through-hole components.2.

Within the PCB assembly facilities board are often worked onin an assembly line. This process allows them to be moves from one section toanother whilst something is added at each stage. The boards can be moved onconveyor belts passing the boards from one state to the next. This process allowsthe board to be worked on quickly as at each section there is something beingworked on and there is never an idle stage. The disadvantages of this are thatit can often take a while to notice something is wrong and by the time that ithas been noticed a considerable number of units may also be defected.3.One of the most crucial parts in the process of surface mountassembly is applying the solder paste to the printed circuit board (PCB). The aim of this process is to deposit the correct amount of solder paste on toeach pad in order to be soldered with great accuracy.

  This is done by usinga stencil to print the paste through. The same procedure can also be applied byjet printing. It is this procedure that it usually accountable for themost defects within assembly, however if controlled properly there can be veryfew mistakes.

The most frequently used way of applying solder paste to aPCB using a stencil is a special squeegee blade.  The squeegees are thetools used to apply the solder paste across the stencil and on to thePCB.  They can sometimes be made from polyurethane however they are usuallymade from metal.During the print cycle it is important to apply the rightamount of pressure across the entire length of the blade to ensure a clean wipeof the stencil.  Too little pressure can cause the paste to smear on thestencil and can cause an incomplete transfer of the paste to the PCB.  Toomuch pressure can scrape up too much paste from the board causing excess wearon the stencil and squeegees, and may cause the paste to seep out between thePCB and the stencil.  A typical setting for the squeegee pressure is 0.5Kgof pressure per 25mm of the blade on the squeegee.

Best services for writing your paper according to Trustpilot

Premium Partner
From $18.00 per page
4,8 / 5
4,80
Writers Experience
4,80
Delivery
4,90
Support
4,70
Price
Recommended Service
From $13.90 per page
4,6 / 5
4,70
Writers Experience
4,70
Delivery
4,60
Support
4,60
Price
From $20.00 per page
4,5 / 5
4,80
Writers Experience
4,50
Delivery
4,40
Support
4,10
Price
* All Partners were chosen among 50+ writing services by our Customer Satisfaction Team

In order for the process to run smoothly stencil maintenanceand cleaning must happen regularly during use.  A lot of the automaticprinting machines have a system that can be set to clean the stencil after afixed number of prints using a lint-free material applied with a cleaningchemical such as IPA (IsopropylAlcohol).  The system performs two functions, the first is thecleaning of the underside of the stencil to stop the smearing of the paste, andthe second is the cleaning of the apertures using vacuum to stop the pastecreating blockages.To verify the process, automatic inspection can be used toaccurately check solder paste deposits.  There are two types of solderpaste inspection available which are 2D inspection which checks the area of thepaste deposit and 3D inspection which checks the volume of the paste deposit.http://www.surfacemountprocess.com/solder-paste-printing-process.

html4.  pick-and-place machines or Pare robotic machines which are used to place surface mountdevices (SMDs) onto a printed circuit board (PCB). They are usedfor high speed, high precision placing of broad range of electronic components,like capacitors, resistors, integrated circuits onto thePCBs which are in turn used in computers, consumer electronics as well asindustrial, medical, automotive, military and telecommunications equipment.

Themachines are programmed with the information of where to place certaincomponents and can work in groups pacing multiple components together or in an assemblyline fashion where one piece is placed and is then moved along to the next machine5.Reflow soldering is a process in which multiple componentsare temporarily secured to a PCB before a controlled temperature is applied andfixes the components in place on the board6.7.8. The basic equipment used during the process is a conveyorthat moves the PCB through the different zones, a pan of solder used in thesoldering process, a pump that produces the actual wave, the sprayer for theflux and the preheating pad. The solder is usually a mixture of metals. Atypical leaded solder has the chemical makeup of 50% tin, 49.5% lead, and 0.5%antimony.